Octane
New Member
Sorry for my bad english =/
Posts: 18
|
Post by Octane on Jan 20, 2009 13:40:23 GMT -5
Dear All. I have a doubt about the FS MT king Kong battery pack format (Receiver 6v). I have in my house 1 battery pack format that have this format fs-racingart.com/detail.php?pid=817I have the smaller and bigger size of this battery pack. But, i don't know if the MT uses the same battery pack format. Can you confirm if i can use my current battery, or i ned to buy this battry pack www.headrushhobbies.com/admin/prod_images/flatpackrec.batterynimh6v1100mah2.JPGI need this information because everything here in Brazil is expensive. So, everything that the car will need, i have to buy and send with the RC car to save money (freight cost + Taxes). Thank you.
|
|
sickboy
Full Member
hey hook me up with another fs www.fshopups.com
Posts: 187
|
Post by sickboy on Jan 20, 2009 14:11:54 GMT -5
|
|
Octane
New Member
Sorry for my bad english =/
Posts: 18
|
Post by Octane on Jan 20, 2009 14:23:59 GMT -5
Wow!!! 1800mah is not sufficient. When you say a long runing, on average how many hours you refer? (In my case, I will use the original servos) thank you again sickboy for the confirmation.
|
|
sickboy
Full Member
hey hook me up with another fs www.fshopups.com
Posts: 187
|
Post by sickboy on Jan 20, 2009 14:34:24 GMT -5
hi well i my self use the battery for about 2hours then go back to a slow charge and then I'm fit to go again and also as you will know your self it also depends on the driving style like lots of corners can drain the battery I take with me most of the time 2x the hump back battery 4600 mah then it gives me a peace of mind
|
|
|
Post by rcrallyfan on Jan 20, 2009 14:47:37 GMT -5
Wow!!! 1800mah is not sufficient. When you say a long runing, on average how many hours you refer? (In my case, I will use the original servos) 1800 mAh may or may not get you through 2 tankfulls... Make sure they give you two of those original servos if possible, one is just not enough.
|
|
Octane
New Member
Sorry for my bad english =/
Posts: 18
|
Post by Octane on Jan 20, 2009 14:57:21 GMT -5
Woaw. the electric consumption of the car 1/5 is very very very different from 1/8 scale. AMAZING!!! About the servos. I will get only one, that's because i don't like the GWS servos too much. I always had problem (broken Gears) with this servos for 1/8 scale (totally of 3 broken servos). I don't know if the 1/5 scale have this same problem. So, I will change the steering servo to Hitec or Futaba mentioned in the forum. To install 2 steering servo, The original receiver support this function or i need change to another receiver? thank you guys
|
|
|
Post by rcrallyfan on Jan 20, 2009 15:11:02 GMT -5
Bear in mind that a "tankful" in 1/5 could be over thirty minutes, possibly even 45 minutes... The Inferno GT that you have (and I did) weighs some 3.5 kilos if I recall right, and a 1/5 weighs over 12 kilos... So the forces the servos deal with are far greater. To use a dual servo setup, all you need is a Y-harness (to connect two servos to your receiver). So yes, the stock or any other receiver supports this. Here's is what the Y-harness is (at a good price, too): www.junun.org/MarkIII/Info.jsp?item=59#
|
|
Octane
New Member
Sorry for my bad english =/
Posts: 18
|
Post by Octane on Jan 21, 2009 7:51:08 GMT -5
Thank you rcrallyfan. It's very simple to install 2 steering servo All my doubts are clearly now. Thanks to all. Now I can buy the car without worries. ;D
|
|